详细描述
|
ES2系列型号 ES2 Series Model |
026T | |||
|
额定电流输出 Rated Current Output |
26A | |||
|
电源 Power Supply |
三相380VAC Three-phase 380V/AC |
|||
|
冷却方式 Type of cooling |
风冷、强制风冷 Natural air cooling ,forced air cooling | |||
|
主回路控制方式 Mode of Main Loop Control |
SVPWM 控制 SVPWM control |
|||
|
反馈电阻 Feedback Resistor |
外置 External | |||
|
使用环境 Operating Environment |
温度 Temperature |
工作情况温度:-10°℃~40°℃(情况温度在40°℃~50°℃,请降额使用」「不冻结」 Working environment temperature:-10°℃~40°C(If ambient temperature ranges from40°C~50°C , please de-rate for use)(no frozing) 储存温度:-20°℃~+85°C「不冻结」Storage temperature:-20°C~85°C 「 no frozing 」 |
||
|
湿度 Humidity |
小于90%,无结露 Less than90%,no condensation | |||
|
防护等级 Level of Protection |
IP20 | |||
|
海拔高度 Altitude |
<1000m (海拔1000m以上,请降额适用) <1000m(if the altitude is over 1000m,please de-rate for use) |
|||
|
振动 Vibration |
≤0.6G ( 5.9m/s2 ) 10-60Hz非连续运行 ≤0.6G ( 5.9m/s2 ) 10-60Hz discontinuous operation |
|||
|
位置控制模式 Position Control Mode |
脉冲指令模式 Pulse Command Mode |
脉冲+符号; Pluse+symbol; A相+B相;Plase A+Plase B; CCW脉冲+CW脉冲。CCW pulse+CW pulse |
||
|
最大输入脉冲频率 Max Output Pulse Frequency |
脉冲+标识:500Kpps ; Pluse+symbol:500Kpps CCW脉冲+CW脉冲:500Kpps ; ccw pulse+Cw pulse:500Kpps A相+B相:单相500Kpps ; Plase A+Plase B : single phase 50OKpps; 开集极传输方式:200Kpps。Open collector transmission:200Kpps |
|||
|
指令控制方式 Command Control Mode |
外部脉冲控制/内部寄存器控制(PR mode) External pulse control / internal position control (PR mode) |
|||
|
指令平滑方式 Command Smoothing Mode |
低通及曲线平滑滤波 Low pass and curve smoothing filtering |
|||
|
电子齿轮比 Electronic Gear Ratio |
电子齿轮比:N/M「N:1~2147483647/M:1~2147483647」 Electronic gear ratio:N/M(N:1~2147483647/M:1~21474836470) |
|||
|
转矩限制 Torque-speed Limit |
参数设定方式Parameter setting mode |
|||
|
速度控制模式 Speed Control Mode |
模拟指令输入 Analog Comm and Input |
电压范围 VoltageScope |
-10V~+10V | |
|
分辨率 Resolution |
12-bit | |||
|
输入阻抗 Input Resistance |
1MΩ | |||
|
时间常数 Time Constant |
25us | |||
|
速度控制范围 Scope of Speed Control |
1:600 | |||
|
指令控制方式 Command Conteol Mode |
外部模拟指令控制/内部寄存器控制 Exterral analog command control/intermal resister control |
|||
|
指令平滑方式 Command Smoothing Mode |
低通平滑滤波;S曲线平滑滤波 Low pass and smoothing filtering;s curve smoothing filtering |
|||
|
转矩限制 Torque-speed Limit |
参数设定方式或模拟输入 Parameter setting mode or analog input |
|||
|
频宽 Bandwidth |
最大1.2kHZ(闭环) MAX.1.2k Hz(closed loop) |
|||
|
扭矩控制模式 Torque Control Mode |
模拟指令输入 Analog Command Input |
电压范围 voltage Scope |
-10V~+10v | |
|
分辨率 Resolution |
12-bit | |||
|
输入阻抗 Input Resistande |
1MΩ | |||
|
时间常数 Time Constant |
25us | |||
|
指令控制方式 Command Control Mode |
外部模拟指令控制/内部寄存器控制 Exterral analog command control/intermal resister control |
|||
|
指令平滑方式 Command Smoothing Mode |
低通平滑滤波 Low pass and smoothing filtering | |||
|
速度限制 Speed Limit |
参数设定方式或模拟输入 Parameter setting mode/analogy input | |||
|
数字 Digital |
输入 Input |
1、伺服使能Servo enabled 2、报警清除Alarm Reset 3、正向极限限制Forward Limit Restrictions 4、反向极限限制Reverse Limit Restrictions 5、脉冲指令制止Pulse Command Suppression 6、零速钳位Zero Speed 7、偏差清零Deviation reset 8、外部力矩限制External Torque- speed Limit 9、控制模式切换Control Mode switch 10、增益切换选择1 Gain Switching1 11、增益切换选择2 Gain Switching2 14、里面速度选取1 Internal Speed Selectl 15、里面速度选择2 Internal Speed Select2 17、电子凸轮啮合Electronic Cam Toothing 20、内里转矩选择1 Internal Torque- speed Select 21、内里车转矩选拔2 Internal Torque-speed Select2 24、电子齿轮比采用1 Electronic Gear Ratio Select1 25、电子齿轮比采取2Electronic Gear Ratio Select2 26、速度指令标的目的选择1 Speed Command DirectionSelec1 27、速度指令目标拔取2 Speed Command Direction Select2 |
28、速度力矩指令目标取反Speed Command Direction Reverse 29、紧急停车 Emergency Sto 32、开动原点回归Original-point Regression Initiate 33、原点回归参考点 Original-point Regression Reference Point 36、内部位置运行开动暗记Start Signal for InternalPosition Running 37、电机暂停Motor Pause 38、内部场所选拔0 nternal Position Select0 39、里面位置选拔1 Internal Position select1 40、里面地点选拔2 Internal Position Select2 41、内部场所选取3 Internal Position Select3 42、内里场所选取4 Internal Position Select4 44、全闭环内外部编码器切换 Full-dosed Internal/External Encoder Switching 45、全闭环内外部编码器误差清零 Full-closed Internal /External Encode Error Reset 53、正向点动Forward Limit restrictions 54、反向点动Reverse Limit Restrictions 55、EV变乱EV Event-triggered Command |
|
|
输出 Output |
1、伺服准备好Servo Ready 2、报警输出Alarm Output 3、定位完成Positioning Finish 4、电磁制动Electromagnetic Braking 5、速度达到Speed Achieve 6、力矩达到Torque Achieve 7、零速达到2ero- speed Signal 8、原点回归完成 Original-point Regression Finish 9、转矩限制orque-spee 10、速度限制Speed Limit 11、警告输出Alarm Output 12、凸轮角度输出Cam Speed Output |
13、内部地点命令完成 Internal Position CommandFinish |
||
|
保护功能 Protection Function |
输入输有缺相保障、超速、过流、过压、欠压、过热、制动变态、过载、地方超差、编码器变态等 Input /output phase lossprotection, over-speed, over-current, over-voltage, under-voltage, over-heating,abnormal braking over-load, posi tion ultra-error, abnormal encoder, etc. |
|||
|
通讯功能 Communication Function |
RS-485/USB |
|||
|
注:Note:
1、TN系统:电力系统的中性点直接和地面,曝露在外之金属元件经由保障性的接地导体毗邻到地面。
2、单相电源机种使用单相三线电力系统。 |
||||
| 型号 | 单位 | W | H | D | W1 | H1 | H2 | SCREW |
| ES2-026T | mm | 123 | 250 | 210 | 108 | 238 | 273 | 4-M5 |
扫一扫
关注公众号